如何确定硬化混凝土的干燥收缩?
|目的
该测试方法描述了在水分含量变化的情况下确定混凝土样本长度的干燥收缩或变化的过程。
仪器
- 一种长度测量装置,其具有能够精确地测量长度至0.005mm的拨号计。(见下图)
- 干燥烘箱能够保持50±1的温度0.
测试样品制备
- 测试样品由标本组成,该样品符合以下尺寸。
长度 | 深度 | 宽度 |
可以从15厘米到30厘米变化 | 7.5 cm | 7.5 cm |
- 根据所需的尺寸铸造混凝土试样,并将其存放在潮湿的空气中3至7天。
- 在标本的每一端的中心钻一个浅凹陷,使其可以容纳6.5毫米直径的钢球。通过用整洁的快速硬化的波特兰水泥固定球,这些钢球固定在这种凹陷中。
- After fixing the steel balls, clean the balls to remove any cement adhering to it and then apply lubricating grease to prevent corrosion.
- 然后将试样保持在潮湿条件下至少24小时,以便使水泥硬化。24小时后,将试样浸入水中保持在24至30的水中0.c直到28天。(记住从铸造标本的一天开始计算NO O F天)
Test Procedure
- After removing the specimens from water, clean the grease from the balls and immediately measure the length of the specimen to an accuracy of 0.005mm by the length measuring apparatus.
- 然后将样品干燥至少44小时。干燥44小时后,将其从烘箱中取出并冷却液体中至少4小时。冷却后,再次使用长度比较器测量样品的长度。将此阅读记录为“原始湿法测量'。
- Repeat the process of oven drying, cooling and measuring until constant length is attained, that is , when the difference between two consecutive length measurement readings is less than 0.01 mm for a 15 cm specimen and proportionately greater for larger specimen. Record the final reading as ‘干测量'。
- 在采取干测量后,测量与球相邻的样本的长度至最接近的0.5毫米,并将其记录为“干长度'。
计算
初始干燥收缩或干燥收缩计算为差异原始湿法测量和干测量表示为百分比干长度。
最初的干燥收缩=[(原湿measurement – dry measurement)/dry length]*100
6评论
如果混凝土混合物旨在在7天达到50MPa的情况下,具体试样可以测试收缩的混凝土试样多大?
先生
硬化混凝土限位的干燥收缩?
感谢Suryakanta此教育信息。这是印度标准的吗?样本类型和多少?您尚未提到过,因为在几乎所有的件中,我读过的收缩率,只能用于收缩测试,它们必须是六个数量。新利18体育官网登录
请解释一下
谢谢你。
铸件的铸造尚不清楚。它应该填充粗骨料或筛分混凝土后。
谢谢你的测试程序。如何确保收缩在限制范围内?您是否知道每台限制值或ACI代码?
The method gives a good understanding on the test procedure. However, it doesn’t state the Standard what has been followed or this procedure is based on. Also If I am not wrong, the length measuring apparatus and the length comparator are not the same (as per ASTM C157).