如何计算SPT值或N值的沙子浅基础的承载力(IS-6403)
|Step-by-Step Procedure for Calculation of Bearing Capacity from Standard Penetration Test Values or N-values
Step-1
Perform标准渗透测试在您想要计算承载力的位置。这是按照IS-2131中给出的标准程序完成的。标准渗透试验必须在垂直方向上每75厘米完成。
Step-2
确定初始计算的深度,宽度和基础的长度。这是一个试验和错误过程。在第一次尝试中,您永远无法获得完全的基础大小,这将满足您的所有需求。
Step-3
申请必要校正标准渗透测试值。计算从基础基础的基础级别的校正SPT值的累积平均值,深度等于基础宽度的2倍。
Step-4
将上述累积平均SPT值与下面给出的相关性相关,以找出相应的剪切电阻角度(φ)。
Step-5
通过将土壤的有效单位重量与基础的深度相乘,计算基础基础基础的有效附加费。
q =υ* dF
在哪里,
q =基础基础的有效附加费,以kgf / cm2
υ=土壤重量,在kgf / cm3.
D.F= Depth of foundation, in cm
Step-6
For the angle of shearing resistance value (ϕ) as calculated inS.tep-4那F一世nd out the corresponding values of bearing capacity factors (i.e. N问:&nϒ下面的表给出)。的中间values of ‘ϕ’, make linear interpolation.
Step-7
Calculate shape factors (i.e. s问:&S.ϒ的)using formula given below.
在哪里,
B =基础宽度,以cm为单位
l =基础长度,以cm为单位
Step-8
Calculate depth factors (i.e. d问:&D.ϒ)使用以下公式。
D.问:=dϒ= 1(对于φ<100.的)
D.问:= dϒ= 1 + 0.1(dF/ b)(nϕ的)1/2(对于φ> 100.的)
N.ϕ使用以下公式计算
N.ϕ= Tan.2[(π/ 4)+(φ/ 2)]
Step-9
计算倾斜因子(即i问:& 一世ϒ)使用下面给出的公式
在哪里,
α=负载倾斜度以垂直度
ϕ = Angles of shearing resistance in degrees
步骤10.
Calculate the correction factor for location of water table using the following formula
W'= 0.5 + 0.5 [D.W./(DF+ b)]
在哪里,
W’ = Correction factor for location of water table
D.W.=水位景深,厘米
D.F= Depth of foundation, in cm
步骤11.
使用下面给出的等式计算净极性承载力。
在哪里,
问:D.= Net ultimate bearing capacity of foundation, kgf/cm2
问:= Effective surcharge at base level of foundation, in kgf/cm2 (ReferS.tep-5的)
N.问:&nϒ=承载能力因素(参见S.tep-6的)
S.问:&S.ϒ=形状因子(参见S.tep-7的)
D.问:&D.ϒ= Depth factors (ReferS.tep-8的)
一世问:& 一世ϒ=倾斜因子(参见S.tep-9的)
W’ = Correction factor for location of water table (ReferS.tep-10的)
B =基础宽度,以cm为单位
υ=批量单位重量的基础土壤,在kgf / cm中3.。
谢谢绅士,这是非常好的工作。
继续努力吧。
好的,它是为了推导尺寸结构基础的承载力,但我需要一个关系来计算60米高的岩石填充大坝的允许承载能力,以在尼泊尔东部的Arun河厚的加等沉积物上成立。
如何在距离表面15米的深度达到冲积沉积物的允许轴承能力,基于DCPT n值,组成有40%巨石的沙质砾石?
How can is it possible to find out the solution if there is both the values of C & Phi ? Can we make Interpolation in such condition? I am asking became there is no any provision of interpolation in IS codes of soil.
I appreciate your knowledge in geotechnical issues.
通过你的评论,我学到了很多,现在有点舒服
thanks sir,
Regards,
Eng. Kahema
在这种情况下,凝聚为阳性为零。如果我们需要使用凝聚力来计算净终极承载力,我们如何找到呢?
非常感谢你先生,你已经让它变得非常简单有效。
请如何推断该区域的承载力?我为它做了5个spts,并且在我打算将我的基础上的2m处的轴承压力分别为20,112,340和400kn / m ^ 2分别用于BH1,BH2,BH3,BH4和BH5。
1)如何计算基于n =值的SBC敬请回复
基金会是安全的40毫米的允许定居点
U can do the sbc caliculation using n value by graph which is there in IS:6403. by that u can get angle of internal friction ….
Thanks very much for such an explicit note.
谢谢Shrikant分享信息..
Thanks Suryakanta for u r wonderful work. The site is quite handy and useful. Although i had not gone thru entire site, but i was browsing geo-tech blog to refresh my basiscs and i found that u had made concepts in a quick and simple steps.
谢谢你分享你的知识,时间和想法。
保持良好的工作。
Sudhakar.
好的帮助